聚合物三腔微管挤出口模结构对胀大变形的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Effect of Polymer Three-Cavity Micro-Tube Extrusion Die Structure on Swell Deformation
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    聚合物熔体的模内流动状态与模外胀大变形直接影响微挤出制品的成型质量。文中基于Carreau模型,采用数值模拟方法,研究了聚合物三腔微管挤出过程中口模壁厚差与空心度结构特征对胀大变形行为的影响。结果表明,影响挤出胀大变形程度的关键因素是口模出口附近的轴向速度分布;内外壁厚差会导致较大壁厚位置处对应的型坯厚度增大,而较小壁厚位置处的型坯厚度减小,壁厚差变化对薄壁区域壁厚变形影响较大,达到91.4%;空心度减小能提升口模出口附近轴向速度分布均匀性,减小了70.1%的变形程度;基于胀大变形规律逆向补偿设计了口模形状与尺寸,明显改善了制品成型质量。研究结果对聚合物多腔微管的口模结构优化设计具有理论意义与工程应用价值。

    Abstract:

    The flow of polymer melt in the die and the swelling deformation of the extrudate directly affect the molding quality of the extruded products. In this study, based on the Carreau model, the numerical simulation method was used to study the influence of die wall thickness difference and hollowness structure characteristics on the swell deformation behavior during the extrusion process of polymer three-cavity micro-tube. The results show that the key factor affecting the extrusion swell deformation is the axial velocity distribution at the outlet of the die. The difference between the inner and outer wall thickness will lead to the increase of the thickness of the extrudate at the larger wall thickness position and the decrease of the smaller wall thickness position, and the change of the wall thickness difference has a great influence on the wall thickness deformation of the thin- walled area, up to 91.4%. When the thickness difference between the inner and outer walls is constant, reducing the hollowness can improve the uniformity of the axial velocity distribution at the die outlet and reduce the extrusion deformation by 70.1% . Finally, the shape of the die was compensated by inverse extrusion, the swell deformation law was verified, and the extrusion molding was significantly improved. The research results can guide the die structure optimization design of polymer multi-cavity micro-tube.

    参考文献
    相似文献
    引证文献
引用本文

刘 磊,李经纬,王鑫杨,刘 奎,杨天洋,赵丹阳.聚合物三腔微管挤出口模结构对胀大变形的影响[J].高分子材料科学与工程,2024,40(1):82-91. Lei Liu, Jingwei Li, Xinyang Wang, Kui Liu, Tianyang Yang, Danyang Zhao. Effect of Polymer Three-Cavity Micro-Tube Extrusion Die Structure on Swell Deformation[J]. Polymer Materials Science & Engineering,2024,40(1):82-91.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2024-03-28
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司