椰棕基硬质聚氨酯泡沫的制备及其性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

海南省降解塑料技术创新中心开放课题(ZDYF2019192)


Preparation and Optimization of Coconut-Based Polyurethane Foam
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    利用微波辅助液化技术将椰棕粉末进行液化制得液化物,以液化物为原料、三乙烯二胺(TEDA)和异辛酸锡(TECH)为复合催化剂、水为发泡剂,与多苯基甲烷多异氰酸酯反应通过一步法制备了硬质聚氨酯泡沫(PURF)。对水发泡制备PURF的条件进行优化,较优的制备条件为催化剂中TEDA和TECH的质量比为4:5、催化剂质量分数为5%、泡沫稳定剂M-8818质量分数为2.5%、发泡剂质量分数为2%,该条件下制备的PURF的压缩强度为223 kPa,超过了大部分生物基PURF。采用傅里叶变换红外光谱对液化物、液化剂和PURF进行表征,通过扫描电镜对泡沫泡孔进行观察。结果显示,所合成的PURF大部分为闭孔,体系中基本没有异氰酸根剩余。使用锥形量热仪对最优PURF进行燃烧行为分析,最大热释放速率(HRR)为250.6 kW/m2。

    Abstract:

    Microwave- assisted liquefaction technology was used to liquefy coconut fiber to obtain liquefied substance. Using liquefied substance as raw material, triethylene diamine (TEDA) and tin isocrylate (TECH) as composite catalyst, water as foaming agent, and polyphenylmethanepolyisocyanate were used to synthesize rigid polyurethane foam (PURF) by one- step reaction. The optimum preparation conditions are as follows, the mass ratio of TEDA and TECH as catalyst is 4:5, catalyst mass fraction is 5%, foam stabilizer M-8818 mass fraction is 2.5%, foaming agent mass fraction is 2%. The compression strength of PURF prepared under these conditions is 223 kPa, which is superior to most biobased PURF. The liquefaction, liquefaction agent and PURF were characterized by Fourier transform infrared spectroscopy (FT-IR), and the foam pores were observed by scanning electron microscopy (SEM). The results show that most of foam pores are obturator, and no isocyanate group is left in the system. A cone calorimeter was used to analyze the combustion behavior of the optimal PURF, and the maximum heat release rate (HRR) is 250.6 kW/m2.

    参考文献
    相似文献
    引证文献
引用本文

张童通,李英教,黎吉辉,林 常,宋 辉,许文茸,张玉苍,徐树英.椰棕基硬质聚氨酯泡沫的制备及其性能[J].高分子材料科学与工程,2024,40(7):10-17. Tongtong Zhang, Yingjiao Li, Jihui Li, Chang Lin, Hui Song, Wenrong Xu, Yucang Zhang, Shuying Xu. Preparation and Optimization of Coconut-Based Polyurethane Foam[J]. Polymer Materials Science & Engineering,2024,40(7):10-17.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2024-09-28
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司