聚己内酯掺杂竹荪多糖的3D打印工艺及性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金面上项目(52375298,51975458);陕西省重点研发计划(2022SF-069)


3D Printing Technology of Dictyophora Polysaccharide Doped Polycaprolactone and Properties
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    3D打印技术在组织工程领域的应用日益受到重视,但聚己内酯(PCL)由于其亲水性和韧性的问题在此领域的应用受到了限制。为此,文中用竹荪提取的多糖物质对PCL进行复合改性,制备了多糖/PCL3D打印支架,旨在改善其力学性能并提高其生物学性能以促进组织工程应用。通过拉伸试验表明,添加多糖后的PCL韧性明显提升且弹性模量更接近于骨组织。接触角试验表明,添加多糖后提高了表面的润湿性,接触角从92°降低至76°。经过体外细胞培养验证,添加多糖后生物相容性有所提高。研究表明,添加1%多糖后的改性支架表现出最优异的亲水性、韧性和生物相容性,且显著增强了成骨细胞的附着。

    Abstract:

    The application of 3D printing technology in tissue engineering has become increasingly important. However, the use of polycaprolactone (PCL) in this field is limited due to its hydrophilicity and toughness constraints. Therefore, in this study, polysaccharides extracted from bamboo fungus were combined with PCL to prepare polysaccharide/PCL 3D printed scaffolds, aiming to improve their mechanical properties and enhance their biological performance for tissue engineering applications. The tensile test show that the toughness of PCL is significantly improved after the addition of polysaccharides, and the elastic modulus approaches that of bone tissue. The contact angle test indicates that the surface wettability is increased after polysaccharide addition, with the contact angle decreasing from 92° to 76° . In vitro cell culture validation demonstrates improved biocompatibility after polysaccharide addition. The experiments show that the modified scaffold with 1% polysaccharides exhibits optimal hydrophilicity, toughness, and biocompatibility, and can significantly enhanced the attachment of osteoblasts. This study provided an important foundation and guidance for further application of PCL in tissue engineering.

    参考文献
    相似文献
    引证文献
引用本文

卢山,何莹,马泽宇,刘建波,秦立果,董光能,张雅利.聚己内酯掺杂竹荪多糖的3D打印工艺及性能[J].高分子材料科学与工程,2024,40(8):78-84. Shan Lu, Ying He, Zeyu Ma, Jianbo Liu, Liguo Qin, Guangneng Dong, Yali Zhang.3D Printing Technology of Dictyophora Polysaccharide Doped Polycaprolactone and Properties[J]. Polymer Materials Science & Engineering,2024,40(8):78-84.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2024-10-25
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司