耐高温聚酰胺PA6T/66的高效制备及性能
作者:
作者单位:

1.郑州大学 材料科学与工程学院,河南 郑州 450001;2.河南省先进尼龙材料及应用重点实验室,河南 郑州 450052

作者简介:

通讯作者:

中图分类号:

基金项目:

河南省重点研发计划项目(231111231900);国家自然科学基金资助项目 (52203051, 52403171);河南省研究生教育改革与质量提升工程(YJS2025GZZ03);河南省自然科学基金青年基金资助项目(252300423452)


Efficient Preparation and Performance of High-Temperature Resistant Polyamide 6T/66
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    “预聚合+固相后聚合”工艺是目前制备耐高温聚酰胺的主要方法之一,但预聚合结束后通常采用高温熔融的方式出料,然后经造粒或破碎后进行固相后聚合。其中高温出料需将釜温加热到预聚物熔点以上,难免造成物料氧化。因此,开发低温高效的出料方法,是“预聚合+固相后聚合”工艺亟待解决的关键技术难题。本文以对苯二甲酸、己二胺和己二酸为原料制备耐高温聚酰胺PA6T/66为例,通过对预聚合反应条件与反应程度的系统研究,探明了低温高效出料的关键控制窗口。结果表明,低温高效“预聚合+固相后聚合”工艺制备的PA6T/66(摩尔比6/4)结晶温度(Tc)为271.4 ℃,熔点(Tm)为305.8 ℃,初始热分解温度为398.9 ℃,拉伸强度为94.3 MPa,弯曲强度为100.6 MPa。同时,相较于传统“预聚合+固相后聚合”工艺,本技术可以实现零间歇操作。因此,所开发的低温高效“预聚合+固相后聚合”工艺在保持产品优异性能的同时,可显著提高制备效率和工艺的连续性,为耐高温聚酰胺的工业生产提供新的思路和方法。

    Abstract:

    The "prepolymerization + solid-state post-polymerization" process is one of the primary methods for preparing high-temperature-resistant polyamides currently. However, after the completion of prepolymerization, prepolymers are usually discharged in melt state. Then, the prepolymers need to be crushed or granulated before proceeding to solid-state post-polymerization. For discharging in melt state, the reactor temperature must be heated above the melting point of the prepolymer, which inevitably leads to oxidation. Therefore, the development of a low-temperature and high-efficiency discharging method is a key technical challenge to be urgently addressed in the "prepolymerization + solid-state post-polymerization" process. Taking the preparation of high-temperature-resistant polyamide PA6T/66 by using terephthalic acid, hexamethylenediamine and adipic acid as raw materials as an example, the key control window for low-temperature and high-efficiency discharging was explored through systematic research on the prepolymerization reaction conditions. The results show that the PA6T/66 (with a mole ratio of 6/4) prepared by the low-temperature and high-efficiency "prepolymerization + solid-state post-polymerization" process has a crystallization temperature (Tc) of 271.4 ℃, a melting point (Tm) of 305.8 ℃, an initial thermal decomposition temperature of 398.9 ℃, a tensile strength of 94.3 MPa, and a bending strength of 100.6 MPa. Meanwhile, compared with the traditional "prepolymerization + solid-state post-polymerization" process, this technology enables the continuous preparation of high-temperature resistant polyamides. Thus, the developed low-temperature and high-efficiency "prepolymerization + solid-state post-polymerization" process not only maintains the excellent performance of the product but also significantly improves the preparation efficiency and process continuity, providing new ideas and methods for the industrial production of high-temperature resistant polyamides.

    参考文献
    相似文献
    引证文献
引用本文
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2025-09-05
  • 录用日期:2025-11-07
  • 网络出版日期:2026-09-04
  • 在线发布日期:
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司