一种环保浸渍体系的制备及其在聚酯纤维/橡胶复合材料中的应用
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家重点研发计划项目(2022YFD2301204)


Preparation of an Environmentally Friendly Impregnation System and Its Application in Polyester Fiber/Rubber Composites
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    室温制备了绿色环保浸渍液,采用两步法浸渍聚酯纤维。首先使用单宁酸(TA)对聚酯纤维进行活化,其次引入甘油三缩水甘油醚(GTE)和2-乙基-4-甲基咪唑(MZ),替代传统间苯二酚-甲醛-胶乳(RFL) 体系中有毒的RF组分对聚酯纤维进行浸渍改性,研究了GTE与MZ的用量比对聚酯纤维/橡胶界面黏合性能的影响。结果表明,当GTE与MZ质量比为4/1 时,剥离力最大,达到6.3 N/根,抽出力也最大,达到47.5 N,纤维表面附胶程度最高,黏合效果最好。

    Abstract:

    A green impregnating solution was prepared at room temperature, and polyester fibers were impregnated by two-step method. Firstly, the polyester fibers were activated using tannic acid (TA), and secondly, glycerol triglycidyl ether (GTE) and 2- ethyl- 4- methylimidazole (MZ) were introduced to replace the toxic RF component in the traditional resorcinol- formaldehyde- latex (RFL) system for impregnating polyester fibers to modify the polyester fibers. And the effect of the dosage ratio of GTE to MZ on the adhesion properties of the polyester fiber/rubber interface was studied. The results show that when the mass ratio of GTE to MZ is 4/1, the peeling force is the largest, reaching 6.3 N/root, and the extraction force is also the largest, reaching 47.5 N, with the highest degree of adhesive attachment on the fiber surface and the best adhesive effect.

    参考文献
    相似文献
    引证文献
引用本文

孙 彤,沈 梅,刘 莉.一种环保浸渍体系的制备及其在聚酯纤维/橡胶复合材料中的应用[J].高分子材料科学与工程,2025,41(5):96-103. Tong Sun, Mei Shen, Li Liu. Preparation of an Environmentally Friendly Impregnation System and Its Application in Polyester Fiber/Rubber Composites[J]. Polymer Materials Science & Engineering,2025,41(5):96-103.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2025-08-31
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司