注射打印工艺的喷嘴设计与流量控制
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(52206095);山东省自然科学基金资助项目(ZR2021QE232);山东省高等学校青创科技支持计划(2023KJ102)


Nozzle Design and Flow Control in Injection Printing Process
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    提出以挤出打印零件外壳为自身模具进行内部注射填充的注射打印增材制造策略,为实现高效高强熔融沉积成型提供了一种解决方案。分析得到了不同打印精度下所允许的注射流量范围及对应的喷嘴口径,探明了不同工序单元的喷嘴结构适配性及其对成型工艺的影响,以兼顾打印和注射工序的工艺需求。结果表明,在打印工序,打印流量与螺杆转速表现出良好的线性正相关关系。小口径喷嘴会引起较大流动阻力,使螺杆末端流体所受压力显著增高,过高的压力和流动阻力会降低挤出打印效率。在注射工序,注射流量与注射速度呈正相关,且熔体注射温升受注射速度和喷嘴口径的显著影响。注射速度过大会导致熔体因温升过高而降解,因此,存在极限注射流量,且其随喷嘴口径的增加而增加。此外,喷嘴口径不能过大,否则会影响打印工序的精度。因此,设计注射打印喷嘴要兼顾打印精度、注射温升和流量需求,以确保成型质量和稳定性。

    Abstract:

    An injection printing additive manufacturing strategy that uses the extruded printed part shell as its own mold for internal injection filling was proposed, providing a solution for achieving efficient and high-strength melt deposition molding. The allowable injection flow range and corresponding nozzle diameter under different printing accuracies was analyzed, the adaptability of nozzle structures for different process units and their impact on the molding process was explored, in order to meet the process requirements of printing and injection processes. The results show that there is a good linear positive correlation between the printing flow rate and screw speed in the printing process. Small diameter nozzles can cause significant flow resistance, resulting in a significant increase in the pressure on the fluid at the end of the screw. Excessive pressure and flow resistance can reduce the extrusion printing efficiency. In the injection process, the injection flow rate is positively correlated with the injection speed, and the temperature rise of melt injection is significantly affected by the injection speed and nozzle diameter. Excessive injection speed can lead to degradation of the melt due to excessive temperature rise, resulting in a limit injection flow rate that increases with the increase of nozzle diameter. In addition, the nozzle diameter should not be too large, otherwise it will affect the accuracy of the printing process. Therefore, when designing injection printing nozzles, it is necessary to consider printing accuracy, injection temperature rise, and flow requirements to ensure the molding quality and stability.

    参考文献
    相似文献
    引证文献
引用本文

朱家威,潘 威,黄士争,Sain Mohini,杨卫民,曾宪奎,鉴冉冉.注射打印工艺的喷嘴设计与流量控制[J].高分子材料科学与工程,2025,41(5):149-158. Jiawei Zhu, Wei Pan, Shizheng Huang, Mohini Sain, Weimin Yang, Xiankui Zeng, Ranran Jian. Nozzle Design and Flow Control in Injection Printing Process[J]. Polymer Materials Science & Engineering,2025,41(5):149-158.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2025-08-31
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司