温度诱导的表面活性聚合物设计合成及其响应行为
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

中国石油科技创新基金研究项目(2024DQ02-0120);国家自然科学基金面上项目(52274037);国家自然科学基金重点项目(51834005);黑龙江省重点研发计划项目(2023ZX04A03)


Design Synthesis and Response Behavior of Temperature-Induced Surface Active Polymers
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    文中聚焦温敏聚合物的响应机理,通过单电子转移活性自由基聚合法(SET-LRP),以溴化亚铜/三-(2-二甲氨基乙基)胺(CuBr/Me6TREN)原位歧化得到的初生零价铜(Cu0)及二价铜与混合配体的络合物(CuIIBr2/Me6TREN/PMDETA)为催化体系,实现了温敏单体N-异丙基丙烯酰胺(NIPAM)和甜菜碱两性离子功能单体[2-(甲基丙烯酰基氧基)乙基]二甲基-(3-磺酸丙基)氢氧化铵(DMMPPS)的原位链延伸,制备得到了系列不同嵌段比的温敏聚合物P(NIPAM-b-DMMPPS)。采用核磁共振氢谱和红外光谱对聚合物结构进行了表征。以NIPAM加料比例为40%合成的P(NIPAM-b-DMMPPS)具有最低临界溶解温度(LCST)和最高临界溶解温度(UCST),分别为41 ℃和25 ℃。考察了NaCl浓度对P(NIPAM-b-DMMPPS) LCST的影响,随着NaCl浓度的增大,LCST略降低。表面张力测试结果表明,表面活性聚合物溶液浓度为1×10-2 g/L时,表面张力降低至45 mN/m。P(NIPAM-b-DMMPPS)在石蜡/水体系中表现出温度诱导的乳化-破乳行为,P(NIPAM-b-DMMPPS)吸附在油水界面形成乳液,提高P(NIPAM-b-DMMPPS)中PNIPAM嵌段的比例能够实现从“低温乳化、高温破乳”向“高温乳化、低温破乳”的转变,其在油水乳化破乳领域有良好的应用前景。

    Abstract:

    Focused on the response mechanism of temperature-sensitive polymers, the Cu0 obtained through in situ disproportionation of cuprous bromide/tris- (2-dimethylaminoethyl)amine(CuBr/Me6TREN) and a complex of divalent copper with mixed ligands (CuIIBr2/Me6TREN/PMDETA) were catalyzed by single electron transfer reactive radical polymerization (SET- LRP), which were used as catalytic. The in situ chain extension of the temperature-sensitive monomer N-isopropylacrylamide (NIPAM) and the betaine amphiphilic functional monomer [2- (methacryloyloxy)ethyl] dimethyl- (3- sulphonatopropyl) ammonium hydroxide (DMMPPS) has been realized, and a series of temperature- sensitive polymers with different block ratios of P(NIPAM- b-DMMPPS) have been prepared. The polymer structures were characterized by 1H-NMR and FT-IR. P(NIPAM-b-DMMPPS) synthesized with a NIPAM addition ratio of 40% has a minimum critical dissolution temperature (LCST) and a maximum critical dissolution temperature (UCST) of 41 °C and 25 °C, respectively. The effect of NaCl concentration on the LCST of P(NIPAM- b- DMMPPS) was examined, and the LCST decreases slightly with increasing NaCl concentration. The results of surface tension measurements show that a surface- active polymer solution concentration of 1×10-2 g/L reduces the surface tension to 45 mN/m. P(NIPAM-b-DMMPPS) exhibits temperature-induced emulsification and demulsification behaviors in the paraffin/water system, and P(NIPAM- b- DMMPPS) adsorbs at the oil-water interface to form an emulsion, improving the efficiency of P(NIPAM- b-DMMPPS) can realize the transition from "low- temperature emulsification and high- temperature demulsification" to "high- temperature emulsification and low-temperature demulsification", showing a good application prospect in the field of oil-water emulsification and demulsification.

    参考文献
    相似文献
    引证文献
引用本文

邹一梅,王 玲,刘向斌,王 俊,丁 伟,苏馨怡,刘潞敏,杨二龙.温度诱导的表面活性聚合物设计合成及其响应行为[J].高分子材料科学与工程,2025,41(7):25-35. Yimei Zou, Ling Wang, Xiangbin Liu, Jun Wang, Wei Ding, Xinyi Su, Lumin Liu, Erlong Yang. Design Synthesis and Response Behavior of Temperature-Induced Surface Active Polymers[J]. Polymer Materials Science & Engineering,2025,41(7):25-35.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2025-10-15
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司