聚碳酸酯型热塑性聚氨酯弹性体对聚碳酸环己撑酯的增韧改性
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

陕西省重点研发项目(2021ZDLGY13-08);陕西省重点研发项目(2023-LL-QY-10);国家自然科学基金青年项目(22404008);陕西省自然科学基金面上项目(2024JC-YBMS-128)


Toughness Enhancement of Poly (cyclohexene carbonate) with Polycarbonate-Based Thermoplastic Polyurethane Elastomers
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    聚碳酸环己撑酯(PCHC)是一种由二氧化碳和环氧环己烷制备得到的脂肪族聚合物,具有极大的应用潜力。为了扩大该聚合物的应用范围,提高其韧性非常关键。文中将聚碳酸酯型热塑性聚氨酯弹性体(PCDL-TPU)作为增韧剂,与PCHC进行共混改性,研究了PCHC/PCDL-TPU共混物的微观结构、结晶行为和热力学性能。结果表明,PCHC和PCDL/TPU都为非结晶型共聚物,PCHC/ PCDL-TPU二者相容性良好,共混物的玻璃化转变温度(Tg)单一,介于PCHCTPU和PCDL-TPU之间。随着PCDL-TPU含量的增加,改性后的PCHC韧性显著增强,冲击强度高达82.92 kJ/m2, 断裂伸长率提升至348%,与未改性PCHC相比,分别提高了约82倍和200倍。

    Abstract:

    Poly (cyclohexene carbonate) (PCHC), an aliphatic polymer synthesized by the copolymerization of carbon dioxide and cyclohexane oxide, which is a promising polymer material due to the utilization of carbon dioxide (CO2). In order to increase the attractiveness of this polymer, it is crucial to enhance its toughness. Herein, thermoplastic polyurethane elastomers based on polycarbonate diol (PCDL-TPU) was used as toughening agent to blend with PCHC by melt blending. The microstructure, crystallization behavior, thermal and mechanical properties of PCHC/PCDL-TPU blends were investigated. The results show that both PCHC and PCDL-TPU are amorphous polymers that exhibit good compatibility when blended together. The blend material shows a single glass transition temperature (Tg), which is between the Tg of the pure polymers. As the composition ratio of PCDL-TPU increases in the blend materials, the toughness of PCHC is significantly enhanced and superior to that of pure PCHC. The impact strength of the blend impressively reaches to 82.92 kJ/m2, the elongation at break is enhanced to 348%, which increase nearly 82 times and 200 times than those of pure PCHC, respectively.

    参考文献
    相似文献
    引证文献
引用本文

杨晨晨,王 佼,刘今乾,李应平,袁 聪,王燕周,吕博学,王珊珊.聚碳酸酯型热塑性聚氨酯弹性体对聚碳酸环己撑酯的增韧改性[J].高分子材料科学与工程,2025,41(7):62-70. Chenchen Yang, Jiao Wang, Jinqian Liu, Yingping Li, Cong Yuan, Yanzhou Wang, Boxue Lü, Shanshan Wang. Toughness Enhancement of Poly (cyclohexene carbonate) with Polycarbonate-Based Thermoplastic Polyurethane Elastomers[J]. Polymer Materials Science & Engineering,2025,41(7):62-70.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2025-10-15
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司