玻纤质量分数对长玻纤增强聚丙烯气辅共注塑管件的质量影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

江西省重点研发计划“揭榜挂帅”项目(20223BBE51012);国家自然科学基金资助项目(52163006,52273033);江西省自然科学基金重点项目(20232ACB204004);江西省研究生创新专项(YC2023-S549)


Effect of Glass Fiber Mass Fraction on the Gas-Assisted Co-Injection Molding Pipes of Long Glass Fiber Reinforced Polypropylene
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以长玻纤增强聚丙烯(LGFR-PP)为外层材料,聚丙烯(PP)为内层材料,通过气体辅助共注塑工艺(GACIM)制备管件,对比研究了玻纤含量对管件壁厚、玻纤沿着轴向方向取向分布及抗压强度的影响。结果表明,玻纤取向程度在管件径向方向呈现由外向内逐渐增强的趋势,外层熔体可明显分为3层结构,且各层中的玻纤取向存在显著差异;随着玻纤含量从10%增至40%,管件的总壁厚和内层壁厚均呈现先上升后下降的变化趋势,而外层壁厚则表现为持续上升;当玻纤含量为30%时,管件的总壁厚和内层壁厚分别达到最大值,为2.61 mm和1.14 mm;管件的抗压强度随着玻纤含量的增加逐渐提升,但增长速率逐渐放缓。

    Abstract:

    Gas- assisted co- injection molding (GACIM) pipe fittings were prepared with polypropylene as inner layer and long glass fiber reinforced polypropylene material as outer layer, and the effects of different glass fiber contents on the wall thickness, longitudinal orientation distribution and pressure resistance of the pipe fittings were compared and studied. The experimental results show that the orientation of glass fiber increases from outside to inside along the radial direction of the pipe fittings; the outer melt is divided into three layers, the distribution orientation in these three layers is different; when the glass fiber content varies from 10% to 40%, the total wall thickness and inner wall thickness increase first and then decline, while the outer wall thickness increases gradually. When the content of glass fiber is 30% , the total wall thickness and outer wall thickness reaches the maximum value of 2.61 mm and 1.14 mm respectively; with the increase of glass fiber content, the pressure resistance gradually increases, but the growth rate gradually slows down.

    参考文献
    相似文献
    引证文献
引用本文

孔垂鑫,匡唐清,柳和生,杨 帆,刘家豪.玻纤质量分数对长玻纤增强聚丙烯气辅共注塑管件的质量影响[J].高分子材料科学与工程,2025,41(7):94-101. Chuixin Kong, Tangqing Kuang, Hesheng Liu, Fan Yang, Jiahao Liu. Effect of Glass Fiber Mass Fraction on the Gas-Assisted Co-Injection Molding Pipes of Long Glass Fiber Reinforced Polypropylene[J]. Polymer Materials Science & Engineering,2025,41(7):94-101.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2025-10-15
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司