60 ℃条件下尼龙6的熔融和重结晶行为
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

温州市重大科技创新“揭榜挂帅”攻关项目(ZG2023044);安徽省重点研发计划(202304a05020081)


Melting and Recrystallization of Nylon 6 at 60 ℃
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    在工业生产尼龙6产品的过程中,常在玻璃化转变温度(Tg=60 ℃)进行退火,在后续加工过程中会伴随着重结晶过程的发生。文中通过快速差示扫描量热仪(FSC)表征在60 ℃退火结晶的尼龙6,观察其在升温速率10~20000 K/s范围内的重结晶行为。结果显示,其初始晶体熔点为64 ℃,仅比退火温度高4 K,此时晶体完整度低。另外,当升温速率高于1000 K/s时候,冷结晶峰在升温曲线上消失。当升温速率为20000 K/s时,仅有1个吸热峰在升温曲线被观察到,说明重结晶在该升温速率下能被抑制。

    Abstract:

    In the industrial production of nylon 6 products, there is often an annealing process at the glass transition temperature (Tg=60 ° C), and the accompanying crystallization often leads to recrystallization in the subsequent processing. In this study, a fast scanning calorimeter (FSC) was used to characterize the recrystallization behavior of nylon 6 that was crystallized at 60 °C. The results show that the initial melting point of the crystals is 64 ° C, which is only 4 K higher than the annealing temperature, and the degree of crystal perfection is low. In addition, when the heating rate is higher than 1000 K/s, the cold crystallization peak disappears on the heating curve. When the heating rate is 20000 K/s, only one endothermic peak is observed in the heating curve, indicating that recrystallization is inhibited at this heating rate.

    参考文献
    相似文献
    引证文献
引用本文

张 睿,于博士,杜梦雪,Katalee Jariyavidyanont,徐 董,Christoph Schick,René Androsch.60 ℃条件下尼龙6的熔融和重结晶行为[J].高分子材料科学与工程,2025,41(7):102-108. Rui Zhang, Boshi Yu, Mengxue Du, Katalee Jariyavidyanont, Dong Xu, Christoph Schick, René Androsch. Melting and Recrystallization of Nylon 6 at 60 ℃[J]. Polymer Materials Science & Engineering,2025,41(7):102-108.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2025-10-15
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司