短玻纤增强聚丙烯的玻纤含量对液态二氧化碳驱动浮芯辅助注塑管件的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

江西省自然科学基金重点项目(20232ACB204004);国家自然科学基金资助项目(52273033,52163006);江西省重点研发计划“揭榜挂帅”项目(20223BBE51012)


Effect of Glass Fiber Content of Short Glass Fiber Reinforced Polypropylene on Liquid Carbon Dioxide-Powered Projectile Assisted Injection Molding Pipes
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    文中基于实验方法探究了短玻纤含量对液态二氧化碳驱动浮芯辅助注射(LCO2-PAIM)工艺成型管件玻纤断裂剩余长度、壁厚、玻纤取向及耐压性能的影响。研究发现,随着短玻纤质量分数的增加,有效降低了管件的平均玻纤断裂剩余长度,提升了管件的耐压性能,但含量过高又会降低管件的壁厚均匀性和耐压性能。此外,短玻纤含量对管件玻纤取向的影响具有一定的规律性,不同含量的玻纤取向分布规律大致相同,且质量分数为20%时玻纤取向最差。这些结论不仅为LCO2-PAIM工艺中短玻纤含量的优化提供了理论依据,也为其他复合材料注射成型工艺中短玻纤含量的选择提供了参考。

    Abstract:

    Based on the experimental method, the effects of short glass fiber content on glass fiber breakage residual length, wall thickness, glass fiber orientation, and compression resistance of pipe fittings molded by liquid carbon dioxide-powered projectile-assisted injection molding (LCO2-PAIM) process were investigated. It is found that increasing the mass fraction of short glass fibers could effectively reduce the average remaining glass fiber breakage length and improve the compression resistance of the tubes, but too much high glass fiber content could reduce the wall thickness uniformity and compression resistance of the tubes. In addition, the effect of short glass fiber content on the glass fibers orientation of the pipe fittings follows a certain regularity, the orientation distribution law of glass fibers with different contents is approximately the same, and the orientation of glass fibers is the worst when the mass fraction is 20% . These conclusions not only provide a theoretical basis for the optimization of short glass fiber content in LCO2-PAIM process, but also provide a reference for the selection of short glass fiber content in other composite material injection molding processes.

    参考文献
    相似文献
    引证文献
引用本文

彭 杰,匡唐清,柳和生,杨 帆,梁健康,金廷翁.短玻纤增强聚丙烯的玻纤含量对液态二氧化碳驱动浮芯辅助注塑管件的影响[J].高分子材料科学与工程,2025,41(7):109-116. Jie Peng, Tangqing Kuang, Hesheng Liu, Fan Yang, Jiankang Liang, Tingweng Jin. Effect of Glass Fiber Content of Short Glass Fiber Reinforced Polypropylene on Liquid Carbon Dioxide-Powered Projectile Assisted Injection Molding Pipes[J]. Polymer Materials Science & Engineering,2025,41(7):109-116.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2025-10-15
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司