超高分子量聚乙烯锂电池隔膜湿法工艺及性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

山东省重点研发计划资助项目(2024CXGC010217)


Wet Manufacturing Processes and Performance of UHMWPE Separator for Lithium-Ion Batteries
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    文中针对超高分子量聚乙烯(UHMWPE)锂电池隔膜湿法制备工艺,研究了螺杆转速和熔体温度对 20%固含量UHMWPE/石蜡油(LP)共混物挤出及微孔膜性能的影响。结果表明,适当提高熔体泵前压力可提高挤出稳定性,不同转速下铸片中的含油量没有明显波动,转速在 70~120 r/min 范围内,UHMWPE 与 LP 的塑化效果较好。转速升高会使铸片相对分子质量降低,转速超过 100 r/min 时,相对分子质量下降明显。转速为 90 r/min 时,UHMWPE 分子链骨架结构较强,微孔膜的微孔大小均匀性好,此时微孔膜的力学性能也较高。不同熔体温度挤出结果表明,随着温度从210 ℃升高到 250 ℃,铸片微观褶皱结构更加细密,并有利于微孔膜成孔。铸片相对分子质量及微孔膜的拉伸强度和穿刺强度都随温度升高而降低,隔膜热收缩率则随温度升高而增大。

    Abstract:

    The wet manufacturing process of ultra- high molecular weight polyethylene (UHMWPE) lithium- ion battery separators was investigated, and the effects of screw speed and melt temperature on the extrusion and performance of 20% solid content UHMWPE/paraffin oil (LP) blends were examined. Experimental results demonstrate that increasing the melt pump pressure appropriately can enhance the extrusion stability. The oil content in the cast films shows no significant fluctuations at different speeds ranging from 70 r/min to 120 r/min, indicating good plasticization effects of UHMWPE and LP at these speeds. Higher speeds lead to reduced molecular weight of the cast films, with a notable decrease observed beyond 100 r/min. At a rotational speed of 90 r/min, the molecular chain framework of UHMWPE is strengthened, resulting in improved uniformity of micro- pores in the membrane and enhanced mechanical properties. Extrusion at different melt temperatures reveals that higher temperatures result in finer microscopic wrinkle structures in the cast films, facilitating pore formation in the micro-porous membrane. However, increasing temperature reduces the molecular weight of the cast films, as well as the tensile and puncture strengths of the membrane, while increasing thermal shrinkage.

    参考文献
    相似文献
    引证文献
引用本文

秦升学,秦亚磊,张 影,董秋春,张弘斌,刘 杰.超高分子量聚乙烯锂电池隔膜湿法工艺及性能[J].高分子材料科学与工程,2025,41(8):10-18. Shengxue Qin, Yalei Qin, Ying Zhang, Qiuchun Dong, Hongbin Zhang, Jie Liu. Wet Manufacturing Processes and Performance of UHMWPE Separator for Lithium-Ion Batteries[J]. Polymer Materials Science & Engineering,2025,41(8):10-18.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2025-12-05
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司