压力诱导聚乳酸晶体微纤化及强韧化机理
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

湖北省自然科学基金资助项目(2022CFB511);湖北省教育厅科学技术研究计划重点项目(D20221405);国家自然科学基金资助项目(51703054)


Pressure Induced Micro-Fibrillation of Polylactic Acid Crystals and Its Strengthening and Toughening Mechanism
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    通过成型加工新方法形成特殊的微纤结构是实现聚合物高性能化的有效途径之一。文中通过压力诱导流动(PIF)成型成功制备了高性能聚乳酸(PIF-PLA)制品。研究了 PIF 成型压力对 PLA 晶体结构的演变以及对性能的影响。结果表明,经过 PIF 成型之后,PLA 球晶演变为沿流动方向取向的微纤结构,但过高的压力(≥ 240 MPa)会使晶片在流动取向过程中发生相互干涉,形成局部紊乱区域。PIF-PLA 样品中形成了部分 α′晶,并且结晶度随着施加压力的增加而降低。取向程度随着施加压力的增加出现先增加后降低的变化趋势。PIF-PLA 样品的玻璃化转变温度高于纯PLA 样品 10~15 ℃。拉伸强度、断裂伸长率及冲击强度均随着成型压力增加出现先增加后降低的变化趋势,拉伸强度在压力为 180 MPa 时达到最大值 148.4 MPa,冲击强度在 120 MPa 时达到最大值 117.6 kJ/m2。最后,提出了 PIF 成型中PLA 球晶微纤化的演变模型及强韧化机理,为结晶聚合物的高性能化开辟了一条新途径。

    Abstract:

    It is one of the effective ways to achieve high performance of polymers with the formation of special microfiber structures through new molding process. In this paper, high performance polylactic acid sample (PIF-PLA) was successfully prepared by pressure induced flow (PIF) molding. The effect of PIF molding pressure on the crystal structure evolution and properties of PLA was studied. The results show that, PLA spherulites evolve into microfiber structures oriented along the flow direction after PIF molding. However, mutual interference of lamella would appear during the flow orientation process at excessively high pressure (≥240 MPa), forming a local disturbed area. It is found that part of α′crystals are formed, and the crystallinity decreases with the increase of applied pressure in the PIF- PLA sample. The degree of orientation increases first and then decreases with the increase of pressure. The glass transition temperatures of PIF-PLA samples are 10~15 ℃higher than that of pure PLA samples. The tensile strength, elongation at break as well as the impact strength increase first and then decrease with the applied pressure. The tensile strength reaches the maximum of 148.4 MPa when the applied pressure is 180 MPa, and the impact strength reaches the maximum of 117.6 kJ/m2 at the applied pressure of 120 MPa. Finally, the evolution model of PLA spherulite micro- fibrillation during PIF processing, and the strengthening and toughening mechanism were proposed, which develop a new way for the high performance of crystalline polymers.

    参考文献
    相似文献
    引证文献
引用本文

余 鹏,王东明,李丽芬,邓雯昕,熊少峰.压力诱导聚乳酸晶体微纤化及强韧化机理[J].高分子材料科学与工程,2025,41(8):35-42. Peng Yu, Dongming Wang, Lifen Li, Wenxin Deng, Shaofeng Xiong. Pressure Induced Micro-Fibrillation of Polylactic Acid Crystals and Its Strengthening and Toughening Mechanism[J]. Polymer Materials Science & Engineering,2025,41(8):35-42.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2025-12-05
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司