感应加热元件对热塑性复合材料感应焊接接头性能的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

天津市教委科研计划(2021KJ051); 国家重点研发计划(2023YFB4302400)


Effect of Induction Heating Elements on the Properties of Induction Welded Joints of Thermoplastic Composites
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    针对航空结构用碳纤维增强聚苯硫醚热塑性复合材料(CF/ PPS)结构连接问题, 采用热压法制备了 SS-250,SS-300 和 SS-325 3 种金属丝网与热塑性树脂复合感应加热元件, 并对其温度场与产热特性进行了测试分析; 同时, 采用感应焊接对 CF/ PPS 层板进行了焊接, 通过单搭接剪切强度测试与断口形貌分析, 探究了感应加热元件对焊接接头性能的影响。 结果表明, 感应加热元件中金属丝网孔径越小, 产热效率越高, SS-325 热效率最佳(平均升温速率可达15 ℃ / s); 采用 SS-300 感应元件焊接的接头剪切强度最大, 为 19.95 MPa, 单搭接剪切失效模式为 CF/ PPS 层板和感应加热元件撕裂混合失效断裂; SS-250 焊接接头强度次之, 为 18.07 MPa; SS-325 焊接接头强度为 16.01 MPa, 失效模式转变为感应加热元件与 CF/ PPS 层板间界面脱黏失效。

    Abstract:

    In response to the structural connection problem of carbon fiber reinforced polyphenylene sulfide thermoplastic composites for aerospace structure, SS-250, SS-300 and SS-325 composite induction heating elements with metal wire mesh and thermoplastic resin were prepared by hot pressing method, and their temperature field and heat production characteristics were measured and analyzed. At the same time, the CF / PPS laminates were welded by induction welding, and the influence of induction heating elements on the properties of welded joints was investigated by single lap shear strength test and fracture morphology analysis. The results show that the smaller the diameter of wire mesh in the induction heating element, the higher the heat production efficiency, and the thermal efficiency of SS-325 is the best (average heating rate can reach 15 ℃ / s) . The shear strength of the joint welded with SS-300 induction element is 19.95 MPa, and the shear failure mode of the single lap joint is CF / PPS laminates and induction heating element tear and mixed failure fracture. The strength of SS-250 welded joint is 18.07 MPa; the strength of the SS-325 welded joint is 16.01 MPa, and the failure mode changes to the interface disbonding failure between the induction heating element and the CF / PPS laminates.

    参考文献
    相似文献
    引证文献
引用本文

路鹏程, 安俊龙, 祖浩轩, 苏景新.感应加热元件对热塑性复合材料感应焊接接头性能的影响[J].高分子材料科学与工程,2025,41(9):1-9. Pengcheng Lu, Junlong An, Haoxuan Zu, Jingxin Su. Effect of Induction Heating Elements on the Properties of Induction Welded Joints of Thermoplastic Composites[J]. Polymer Materials Science & Engineering,2025,41(9):1-9.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2026-02-06
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司