辅助电极静电纺丝及工艺参数的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

江西省新能源工艺及装备中心开放基金(JXNE2020-07); 江西省教育厅科学技术研究项目(GJJ200740 ); 东华理工大学博士基金(DHBK2019169); 核技术应用教育部工程研究中心项目(HJSJYB2021-3)


Auxiliary Electrode Multi-Jet Electrospinning and the Influence of Process Parameters
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    为解决传统静电纺丝一般只产生单股射流、纳米纤维直径大的问题,设计了一种辅助电极静电纺丝装置。采用Comsol 软件对辅助电极平行于喷丝头和垂直于喷丝头2 种分布方式进行仿真,观察了辅助电极在不同空间位置下的电场分布,研究了泰勒锥的电场强度;基于电压、注射速度以及针头和辅助电极距离的调控,分析了辅助电极在不同空间位置对纳米纤维形貌、射流数量及产量的影响。结果表明,辅助电极在平行位置时收集到了直径分布在220~277 nm 的纳米纤维,略小于同等条件下辅助电极在垂直位置时制备的纳米纤维直径(249~338 nm);而且随着电压的增加、喷丝头和辅助电极之间距离的减小,2 种分布配置条件下获得的纳米纤维直径均呈减小的趋势。研究为实现可控制备多射流和高质量纳米纤维提供了依据。

    Abstract:

    To address the issues of traditional electrospinning, which generally produces only a single jet and has larger nanofiber diameters, an auxiliary electrode electrospinning device was designed. COMSOL software was used to simulate two configurations of auxiliary electrodes, parallel and perpendicular to the spinneret, to observe the electric field distribution in different spatial positions of auxiliary electrodes and to study the electric field intensity at the Taylor cone. Based on the control of voltage, injection speed, and needle-to-auxiliary distance, the influence of spatial position of auxiliary electrodes on morphology of nanofibers, the number of jets, and productivity was analyzed. The results show that when auxiliary electrode is positioned parallel, nanofibers with a diameter range of 220~277 nm are collected, slightly smaller than the nanofibers prepared under the same conditions when auxiliary electrode is in the vertical position (249 ~ 338 nm). Moreover, with the increase of voltage and decrease of distance between the spinneret and auxiliary electrode, the diameter of nanofibers obtained under both distribution configurations exhibits a decreasing trend. This study provides a basis for the controllable preparation of multiple jets and high-quality nanofibers.

    参考文献
    相似文献
    引证文献
引用本文

吴宇珂, 刘 晨, 张 斌, 汪志成.辅助电极静电纺丝及工艺参数的影响[J].高分子材料科学与工程,2025,41(10):76-86. Yuke Wu, Chen Liu, Bin Zhang, Zhicheng Wang. Auxiliary Electrode Multi-Jet Electrospinning and the Influence of Process Parameters[J]. Polymer Materials Science & Engineering,2025,41(10):76-86.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2026-03-17
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司