不同分子量高密度聚乙烯水平燃烧过程中的熔体流动性和热解特性
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(52476127); 湖北省教育厅科学研究计划指导性项目(B2021012)


Melt Flowability and Pyrolysis Characteristics of High-Density Polyethylene with Different Molecular Weight During Combustion
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    聚乙烯(PE)燃烧时会产生流滴熔体,加剧火灾危害。目前多数研究集中于垂直燃烧模式中的熔体流滴行为分析,针对水平燃烧模式的流淌燃烧研究不足,且没有涉及相对分子质量等影响熔体流动性的关键因素。文中针对初始相对分子质量分别为10 万、500 万和900 万的聚乙烯样品PE10,PE500 和PE900,收集了其水平燃烧产生的流滴熔体并测试了其旋转黏度,通过热重实验研究了聚乙烯及其熔体的热稳定性和热解动力学参数。研究表明,热辐射强度从25 kW/m2 增加到50 kW/m2 时,聚乙烯的熔体流滴率从0.67 减小至0.58,但同一热辐射强度下不同相对分子质量PE 的熔体流滴率相差不超过0.02。随初始相对分子质量的增加,流滴熔体的旋转黏度、黏流活化能、热解温度和热解活化能均增加。同一温度时,PE900 流滴熔体的旋转黏度约为PE10 流滴熔体黏度的2 倍。流滴熔体的热稳定性低于原样,但3 种聚乙烯及其流滴熔体之间存在热解动力学补偿效应,且流滴熔体之间的热解动力学参数的差异明显小于原样的。

    Abstract:

    During the combustion of polyethylene, lots of melts significantly increase fire hazards. However, most studies have focused on the dripping behavior in vertical combustion mode. The research on the melt flowing behavior in horizontal combustion mode is insufficient and the key factors affecting melt flowability such as molecular weight are not involved. In this paper, three polyethylene samples PE10, PE500 and PE900, respectively corresponding to the average molecular weight of 10×104, 50×104 and 900×104, were studied. The flowing melts were collected from the horizontal combustion measurements and their rotational viscosity was tested. The thermal stability and pyrolysis kinetic parameters were analyzed by TGA. When the radiation heat flux increases from 25 kW/m2 to 50 kW/m2, the mass fraction of collected melt decreases from 0.67 to 0.58. At the same radiation heat flux, the difference among mass fractions of collected melt is less than 0.02. With the increase of initial molecular weight, the rotational viscosity, viscous flow activation energy, decomposition temperature and decomposition activation energy of collected melts increase. The rotational viscosity of PE900 melt is about twice that of PE10 melt at the same temperature. The thermal stability of melt is lower than that of the original PE sample. There is a thermal decomposition kinetics compensation effect among the three samples and their melts. The difference in thermal decomposition kinetics parameters among the melts is significantly less than that among the samples.

    参考文献
    相似文献
    引证文献
引用本文

王 勇, 李 慧, 谢曌璇, 孙诗洋, 王 洁.不同分子量高密度聚乙烯水平燃烧过程中的熔体流动性和热解特性[J].高分子材料科学与工程,2025,41(12):87-94. Yong Wang, Hui Li, Zhaoxuan Xie, Shiyang Sun, Jie Wang. Melt Flowability and Pyrolysis Characteristics of High-Density Polyethylene with Different Molecular Weight During Combustion[J]. Polymer Materials Science & Engineering,2025,41(12):87-94.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2026-03-21
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司