动态聚脲基酰胺弹性体的制备及其高速烧结 3D 打印
DOI:
作者:
作者单位:

四川大学高分子研究所 先进高分子材料全国重点实验室,四川 成都 610065

作者简介:

通讯作者:

中图分类号:

基金项目:

国家重点研发计划项目(2023YFB4603500)


Preparation of a Dynamic Poly(urea-amide) Elastomer for High-Speed Sintering 3D Printing
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    针对聚酰胺弹性体制备工艺复杂、能耗高等问题,以及高速烧结(HSS)制件层间结合力弱、孔隙率大的技术瓶颈,本研究设计了一种高性能动态聚脲基酰胺(PUA)弹性体,通过硬段中形成的酰胺基脲(ASC)动态键实现性能调控。通过流变分析、动态热机械分析(DMA)及热台显微镜观察,明确了聚脲基酰胺弹性体的烧结窗口与熔融行为。优化打印参数后,在扫描速度24 mm/s、层厚0.2 mm条件下获得了力学性能与尺寸精度均较好的制件。进一步采用热处理与真空浸渍后处理策略,利用动态键的热激活特性促进层间愈合,并选用低粘度浸渍液填充孔隙。结果表明,后处理使制件拉伸强度由1.06 MPa提升至18.12 MPa,断裂伸长率由72.4%提高至316.2%,孔隙率显著降低,表面形貌明显改善。本研究为开发高性能、可修复及可回收的3D打印制件提供了新思路。

    Abstract:

    To address the complex fabrication process and high energy consumption of polyamide elastomers, together with the weak interlayer bonding and high porosity of high-speed-sintered (HSS) parts, a high-performance dynamic poly(urea-amide) (PUA) elastomer was designed, with its performance regulated by acylsemicarbazide (ASC) dynamic bonds formed in the hard segments. Rheological analysis, dynamic mechanical analysis (DMA), and hot-stage microscopy revealed the sintering window and melting behavior of the PUA elastomer. After optimization of the printing parameters, parts with good mechanical performance and dimensional accuracy were obtained at a scanning speed of 24 mm s?1 and a layer thickness of 0.2 mm. Thermal annealing and vacuum-assisted infiltration were further applied as post-treatment strategies: the thermally activated dynamic bonds promoted interlayer healing, while the low-viscosity infiltrating liquid filled the internal pores. Consequently, the tensile strength increased from 1.06 MPa to 18.12 MPa, and the elongation at break increased from 72.4% to 316.2%, with markedly reduced porosity and significantly improved surface morphology. This work provides a new strategy for the fabrication of high-performance, repairable, and recyclable 3D-printed parts.

    参考文献
    相似文献
    引证文献
引用本文
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2026-03-17
  • 录用日期:2026-05-14
  • 网络出版日期:2026-10-28
  • 在线发布日期:
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司