双环戊二烯苯酚型环氧树脂改性含酯基热塑型聚酰亚胺及其挠性覆铜板的制备和性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

湖北省科技发展专项(42000025205T00000017602)


Preparation and Properties of Dicyclopentadiene / Phenol-Type Epoxy-Modified Ester-Containing Thermoplastic Polyimide and Corresponding Flexible Copper Clad Laminate
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    针对常规热塑型聚酰亚胺(TPI)在用于挠性覆铜板(FCCL)时粘接强度低和介电常数高的问题,采用低介电的双环戊二烯苯酚型(DCPD)环氧树脂对主链含酯基的可溶性 TPI-10 进行化学改性,构建了“酯基-环氧基”的原位交联体系,实现了介电性能与粘接性能的协同优化。 通过非等温 DSC 确定了改性体系的梯度固化工艺,结合 FT-IR、XRD、TGA、TMA、拉伸试验等测试手段,系统研究了其改性前后结构与性能的变化和关系,并制备了相应的 FCCL 进行应用性能验证。 结果表明,在适量低介电环氧树脂中环氧基与 TPI 中酯基的原位交联改性作用下,其在 10 GHz 时的介电常数由 3.00 降低到 2.81,同时使相应 FCCL 的剥离强度提高超过 1 倍,达到 2.07 N/ mm。 虽然其耐热性、热稳定性、尺寸稳定性、断裂伸长率、吸水率和介电损耗受到一定影响,但均在可接受的范围之内。 通过将适当的活性酯结构集成在 TPI 分子结构中,借助酯基与环氧基的特殊反应,实现了无需额外添加固化剂的条件下,粘接性和介电性的协同调控,为无胶型 FCCL 用高粘接、低介电 TPI 的性能提升或多功能化改性提供了更多的选择。

    Abstract:

    To address the issues of low adhesion strength and high dielectric constant in conventional thermoplastic polyimide ( TPI ) when used for flexible copper clad laminate ( FCCL ), a low-dielectric dicyclopentadiene / phenol-type epoxy resin (DCPD) was employed to chemically modify soluble TPI-10, which contains ester groups in its main chain. This approach established an in-situ cross-linking system based on “esterepoxy” interactions, achieving the synergistic optimization of dielectric and adhesion properties. The gradient curing process of the modified system was determined through non-isothermal DSC, while the changes and relationships in structure and properties before and after modification were systematically investigated by FT-IR, XRD, TGA, TMA, tensile tests, and other methods. Corresponding FCCLs were fabricated to validate application performance. The results show that, through the in-situ cross-linking modification between epoxy groups of low-dielectric epoxy with an appropriate amount resin and ester groups in TPI, the dielectric constant at 10 GHz decreases from 3.00 to 2.81, while the peel strength of FCCL increases by more than doubled, reaching 2.07 N / mm. Additionally, although there are certain effects on heat resistance, thermal stability, dimensional stability, elongation at break, water absorption, and dielectric loss, these remain within acceptable application limits. By integrating suitable reactive ester structures into the TPI molecular framework and leveraging the specific reaction between ester and epoxy groups, this study enables the synergistic control of adhesion and dielectric properties without additional curing agents. This provides more options or convenience for enhancing the performance or multifunctional modification of high-adhesion, low-dielectric TPI for adhesive-free FCCL.

    参考文献
    相似文献
    引证文献
引用本文

牛 翔, 余 洋, 陈文求, 叶 苗, 陈 伟.双环戊二烯苯酚型环氧树脂改性含酯基热塑型聚酰亚胺及其挠性覆铜板的制备和性能[J].高分子材料科学与工程,2026,42(6):88-95. Xiang Niu, Yang Yu, Wenqiu Chen, Miao Ye, Wei Chen. Preparation and Properties of Dicyclopentadiene / Phenol-Type Epoxy-Modified Ester-Containing Thermoplastic Polyimide and Corresponding Flexible Copper Clad Laminate[J]. Polymer Materials Science & Engineering,2026,42(6):88-95.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2026-10-24
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司